Видео

If you skimmed the flywheel, would you reuse the flywheel bolts to mount or new bolts? If using old bolts, could the old bolts with blue threadlocker be used safely?

Find a ball joint ford dana 60 and put the Dodge components (knuckle out) on it. Will be the best swap you ever did

2024 and your video has helped my neglected 2007 STI to be clunk free. Thank you sir and top notch tip for the zerk fitting 👍

She’s a keeper

What green coolant would you prefer to use on these engines ? I read they are two for mazda these years...

Replaced the EGR and still have the check engine light on. Any recommendations?

Having same problem but when I replaced my ripped one it didn’t make a diffrence truck still didn’t want to idle.

Is that to take it to top dead center im replacing an injection pump on a perkins 2160

Run some diesel fuel in there. 5 min. Drai 3:38 n. Add duralube to your oil

changing plugs on motorbikes are much easier.why cars are so difficult?

thanks brian excellent

6:06 - So I'm not the only that removes stupid keys from the computer keyboard ! Ha ! 6.30.24

Breakcleaner is nasty for humans too. Always use protection

شغل جيدا

R u a Rez Mechanic. Cuz u sure do sound like a wanna B

Thanks for the detailed video. What type of bulbs?

Thanks for taking the time to make these vids brother

How do you by pass a 1998 Cadillac DeVille Hester core

Hi from France! Nice vid ! My tractro doesn't start, I think pump doesn't feed injectors enough, do you adjusting to max can solve the prblem and help start ? Thanks

The circuit board/eraser trick is a great new idea for me! I like just soap and water on the plastic & rubber stuff ( yes I use a drain screen in the sink incase those discs were to fall off). The adhesive recommendation is also very helpful. Thank you for sharing your experience!!!

Your speedometer went below zero is because you were driving backwards for a while

You dont have to pull the rear motor off if you spin the piston back in thats why the piston has the 3 notches in it

I have a 2011 Sequoia and my lift gate won't stay closed. The latch piece just loosely opens and wonder if it needs replacing. Everywhere I read it's the door stuck being SHUT. I have the opposite problem. It won't stay closed. My rear window also may be off it's track and wonder if it's related. I put the window all the way down it won't come up, or it struggles and seems to catch eventually and goes up. The lift gate handle still works and sounds fine, so I'm not sure what to make of this lift gate not staying closed. Any help is appreciated. Thank you.

How long should this take for a good mechanic??

What if the plastic is not there and it's just the metal piece inside?

What a great video. Thanks man. So well explained

Tesla started this trend, and they are IMO one of the worst design trends in the automotive industry. There has to be like ten to fifteen better ways to design a flush door handle. Can someone with half a brain invent one positioned where the door handle is but it’s a 2.5” circle ⭕️ and when you push it in anywhere on the big button, the door pops out. This could be entirely mechanical too, for reduced cost and longevity. Bonus points if the face plates are thick body-coloured hardened glass sitting flush on the car door. My MacBook Air trackpad is glass and after years and years of use it remains entirely scratch-free. Flush “door poppers” could be awesome. Someone invent them. These see-saw door rockers are terrible.

Interesting the part where the upper plenum was seated back over the spider was skipped.

When I pull on my door handle the car unlocks the pin pops up. I want to pull it the second time to open the door. It doesn’t want to open the door is that the mechanism because there’s only one cable I believe and when you pull on it it does pop-up the unlock.

How long does the whole job take to complete?

Wait but I don’t have the arrow on mines

question - i have 2019 f150 with just 18k miles - do these purge valves fail at that miles/or age -thanks

Excellent video. I just did this a few weeks ago. It's nerve racking knowing you can completely destroy it. As an engineer, I do cringe when you don't use torque specs. Mechanics tighten things by feel and that's been demonstrated time and time again to be inaccurate and in some areas (aerospace), dangerous. Also, the tightening sequence is not universally outside in. Refer to the Honda OEM shop manual for the sequence. These things have to be done properly and not by some arbitrary and subjective definition of experience. Bolts that are too loose or too tight are equally bad. There is a calculated thermodynamic elastic factor to all bolts and you want to be right on spec from the beginning.

It will be 5000 cash or credit thiefs

Hey Brian! been a fan for years! Keepit going as long as you can. Best regards from Canada.

part numbers???

can the intake and exhaust valves hit each other? Should the cams always move easy or will they get hard to move if you turn them the wrong way?

My car (2015 VW Golf) has been running fine, but 1st plug change is supposed to be at 60K miles, and I just hit 60k. Warmed the car up fully, because some said that would make it easier. Have been working at it over two hours and can't remove ANY of the coil packs..I've pulled hard enough to stretch one of the boots to 1/2 it's diameter., and if wouldn't release. Would spraying silicone between the rubber boot and soak plug well help release it? Is the silicone going to foul the catalytic?

Thanks so much you saved my life from an annoying alarm.👍👍

A "plastic" piece that runs 4x4 in a BMW!!! People still paying high price for them, SMH

Thank You!!

Thanks very informative

What did you do with the two wires from back of new compressor, I have a new compressor installed and don't know what to do with wiring. Thanks!

You do not “ruin” a halogen bulb by just touching it! Oil in your fingers would create a hot spot on the glass, yes, but you can always CLEAN it with rubbing alcohol!

Only tow in tow out. How about caster and camber adustments.

I’m only seeing permatex the right stuff in red at my hardware store. Yours looks black. I’m guessing red is high temp which this application would be the opposite. Could you let me know the stuff you like for anti corrosion .

did you depressurize the fuel system?

Great video. Thanks a lot. 👍🙏

Can't see anything

No filler. Explained very well. 10/10